htop

HTOP(1) User Commands HTOP(1)

NAME

   htop, pcp-htop - interactive process viewer

SYNOPSIS

   htop [-dCFhpustvH]
   pcp-htop [-dCFhpustvH] [--host/-h host]

DESCRIPTION

   htop is a cross-platform ncurses-based process viewer.

   It  is  similar to top, but allows you to scroll vertically and horizontally, and interact using a pointing device (mouse).  You can observe all processes running on the system, along
   with their command line arguments, as well as view them in a tree format, select multiple processes and act on them all at once.

   Tasks related to processes (killing, renicing) can be done without entering their PIDs.

   pcp-htop is a version of htop built using the Performance Co-Pilot (PCP) Metrics API (see PCPIntro(1), PMAPI(3)), allowing to extend htop to display  values  from  arbitrary  metrics.
   See the section below titled CONFIG FILES for further details.

COMMAND-LINE OPTIONS

   Mandatory arguments to long options are mandatory for short options too.

   -d --delay=DELAY
          Delay between updates, in tenths of a second. If the delay value is less than 1, it is increased to 1, i.e. 1/10 second. If the delay value is greater than 100, it is decreased
          to 100, i.e. 10 seconds.

   -C --no-color --no-colour
          Start htop in monochrome mode

   -F --filter=FILTER
          Filter processes by terms matching the commands. The terms are matched case-insensitive and as fixed strings (not regexs). You can separate multiple terms with "|".

   -h --help
          Display a help message and exit

   -p --pid=PID,PID...
          Show only the given PIDs

   -s --sort-key COLUMN
          Sort  by  this  column (use --sort-key help for a column list).  This will force a list view unless you specify -t at the same time.  Sorting in tree mode applies to the direct
          children of each process.

   -u --user[=USERNAME|UID]
          Show only the processes of a given user, or self if omitted

   -U --no-unicode
          Do not use unicode but ASCII characters for graph meters

   -M --no-mouse
          Disable support of mouse control

   --readonly
          Disable all system and process changing features

   -V --version
          Output version information and exit

   -t --tree
          Show processes in tree view. This can be used to force a tree view when requesting a sort order with -s.

   -H --highlight-changes=DELAY
          Highlight new and old processes

   --drop-capabilities[=off|basic|strict]
          Linux only; this option needs to have been enabled at compile-time and requires libcap support at runtime.
          Drop unneeded Linux capabilities.  In strict mode features like killing, changing process priorities and reading process delay accounting information will not work due to fewer
          capabilities being held.

INTERACTIVE COMMANDS

   The following commands are supported while in htop:

   Tab, Shift-Tab
        Select the next / the previous screen tab to display.  You can enable showing the screen tab names in the Setup screen (F2).

   Up, Alt-k
        Select (highlight) the previous process in the process list. Scroll the list if necessary.

   Down, Alt-j
        Select (highlight) the next process in the process list. Scroll the list if necessary.

   Left, Alt-h
        Scroll the process list left.

   Right, Alt-l
        Scroll the process list right.

   PgUp, PgDn
        Scroll the process list up or down one window.

   Home Scroll to the top of the process list and select the first process.

   End  Scroll to the bottom of the process list and select the last process.

   Ctrl-A, ^
        Scroll left to the beginning of the process entry (i.e. beginning of line).

   Ctrl-E, $
        Scroll right to the end of the process entry (i.e. end of line).

   Space
        Tag or untag a process. Commands that can operate on multiple processes, like "kill", will then apply over the list of tagged processes, instead of the currently highlighted one.

   c    Tag the current process and its children. Commands that can operate on multiple processes, like "kill", will then apply over the list of tagged processes,  instead  of  the  cur‐
        rently highlighted one.

   U    Untag all processes (remove all tags added with the Space or c keys).

   s    Trace  process system calls: if strace(1) is installed, pressing this key will attach it to the currently selected process, presenting a live update of system calls issued by the
        process.

   l    Display open files for a process: if lsof(1) is installed, pressing this key will display the list of file descriptors opened by the process.

   w    Display the command line of the selected process in a separate screen, wrapped onto multiple lines as needed.

   x    Display the active file locks of the selected process in a separate screen.

   F1, h, ?
        Go to the help screen

   F2, S
        Go to the setup screen, where you can configure the meters displayed at the top of the screen, set various display options, choose among color schemes, and select  which  columns
        are displayed, in which order.

   F3, /
        Incrementally  search  the  command  lines of all the displayed processes. The currently selected (highlighted) command will update as you type. While in search mode, pressing F3
        will cycle through matching occurrences.  Pressing Shift-F3 will cycle backwards.

        Alternatively the search can be started by simply typing the command you are looking for, although for the first character normal key bindings take precedence.

   F4, \
        Incremental process filtering: type in part of a process command line and only processes whose names match will be shown. To cancel filtering, enter the Filter option  again  and
        press Esc.  The matching is done case-insensitive. Terms are fixed strings (no regex).  You can separate multiple terms with "|".

   F5, t
        Tree  view:  organize  processes by parenthood, and layout the relations between them as a tree. Toggling the key will switch between tree and your previously selected sort view.
        Selecting a sort view will exit tree view.

   F6, <, >
        Selects a field for sorting, also accessible through < and >.  The current sort field is indicated by a highlight in the header.

   F7, ]
        Increase the selected process's priority (subtract from 'nice' value).  This can only be done by the superuser.

   F8, [
        Decrease the selected process's priority (add to 'nice' value)

   Shift-F7, }
        Increase the selected process's autogroup priority (subtract from autogroup 'nice' value).  This can only be done by the superuser.

   Shift-F8, {
        Decrease the selected process's autogroup priority (add to autogroup 'nice' value)

   F9, k
        "Kill" process: sends a signal which is selected in a menu, to one or a group of processes. If processes were tagged, sends the signal  to  all  tagged  processes.   If  none  is
        tagged, sends to the currently selected process.

   F10, q
        Quit

   I    Invert the sort order: if sort order is increasing, switch to decreasing, and vice-versa.

   +, -, *
        When  in tree view mode, expand or collapse subtree. When a subtree is collapsed a "+" sign shows to the left of the process name.  Pressing "*" will expand or collapse all chil‐
        dren of PIDs without parents, so typically PID 1 (init) and PID 2 (kthreadd on Linux, if kernel threads are shown).

   a (on multiprocessor machines)
        Set CPU affinity: mark which CPUs a process is allowed to use.

   u    Show only processes owned by a specified user.

   N    Sort by PID.

   M    Sort by memory usage (top compatibility key).

   P    Sort by processor usage (top compatibility key).

   T    Sort by time (top compatibility key).

   F    "Follow" process: if the sort order causes the currently selected process to move in the list, make the selection bar follow it. This is useful for  monitoring  a  process:  this
        way, you can keep a process always visible on screen. When a movement key is used, "follow" loses effect.

   K    Hide kernel threads: prevent the threads belonging the kernel to be displayed in the process list. (This is a toggle key.)

   H    Hide  user  threads: on systems that represent them differently than ordinary processes (such as recent NPTL-based systems), this can hide threads from userspace processes in the
        process list. (This is a toggle key.)

   O    Hide containerized processes: prevent processes running in a container from being displayed in the process list. (This is a toggle key.)

   p    Show full paths to running programs, where applicable. (This is a toggle key.)

   Z    Pause/resume process updates.

   m    Merge exe, comm and cmdline, where applicable. (This is a toggle key.)

   Ctrl-L
        Refresh: redraw screen and recalculate values.

   Numbers
        PID search: type in process ID and the selection highlight will be moved to it.

COLUMNS

   The following columns can display data about each process. A value of '-' in all the rows indicates that a column is unsupported on your system, or currently  unimplemented  in  htop.
   The names below are the ones used in the "Available Columns" section of the setup screen. If a different name is shown in htop's main screen, it is shown below in parenthesis.

   Command
        The full command line of the process (i.e. program name and arguments).

        If  the option 'Merge exe, comm and cmdline in Command' (toggled by the 'm' key) is active, the executable path (/proc/[pid]/exe) and the command name (/proc/[pid]/comm) are also
        shown merged with the command line, if available.

        The program basename is highlighted if set in the configuration. Additional highlighting can be configured for stale executables (cf. EXE column below).

        The Command column should be the last column in each screen as can get very long and profits from being able to extend its length dynamically.

   COMM The command name of the process obtained from /proc/[pid]/comm, if readable.

        Requires Linux kernel 2.6.33 or newer.

   EXE  The abbreviated basename of the executable of the process, obtained from /proc/[pid]/exe, if readable. htop is able to read this file on linux for ALL the processes  only  if  it
        has the capability CAP_SYS_PTRACE or root privileges.

        The  basename is marked in red if the executable used to run the process has been replaced or deleted on disk since the process started. The information is obtained by processing
        the contents of /proc/[pid]/exe.

        Furthermore the basename is marked in yellow if any library is reported as having been replaced or deleted on disk since it was last loaded. The information is obtained  by  pro‐
        cessing the contents of /proc/[pid]/maps.

        When  deciding  the  color the replacement of the main executable always takes precedence over replacement of any other library. If only the memory map indicates a replacement of
        the main executable, this will show as if any other library had been replaced or deleted.

        This additional color markup can be configured in the "Display Options" section of the setup screen.

        Displaying EXE requires CAP_SYS_PTRACE and PTRACE_MODE_READ_FSCRED.

   PID  The process ID.

   STATE (S)
        The state of the process:
           S for sleeping
           I for idle (longer inactivity than sleeping on platforms that distinguish)
           R for running
           D for disk sleep (uninterruptible)
           Z for zombie (waiting for parent to read its exit status)
           T for traced or suspended (e.g by SIGTSTP)
           W for paging

   PPID The parent process ID.

   PGRP The process's group ID.

   SESSION (SID)
        The process's session ID.

   TTY  The controlling terminal of the process.

   TPGID
        The process ID of the foreground process group of the controlling terminal.

   MINFLT
        The number of page faults happening in the main memory.

   CMINFLT
        The number of minor faults for the process's waited-for children (see MINFLT above).

   MAJFLT
        The number of page faults happening out of the main memory.

   CMAJFLT
        The number of major faults for the process's waited-for children (see MAJFLT above).

   UTIME (UTIME+)
        The user CPU time, which is the amount of time the process has spent executing on the CPU in user mode (i.e. everything but system calls), measured in clock ticks.

   STIME (STIME+)
        The system CPU time, which is the amount of time the kernel has spent executing system calls on behalf of the process, measured in clock ticks.

   CUTIME (CUTIME+)
        The children's user CPU time, which is the amount of time the process's waited-for children have spent executing in user mode (see UTIME above).

   CSTIME (CSTIME+)
        The children's system CPU time, which is the amount of time the kernel has spent executing system calls on behalf of all the process's waited-for children (see STIME above).

   PRIORITY (PRI)
        The kernel's internal priority for the process, usually just its nice value plus twenty. Different for real-time processes.

   NICE (NI)
        The nice value of a process, from 19 (low priority) to -20 (high priority). A high value means the process is being nice, letting others have  a  higher  relative  priority.  The
        usual OS permission restrictions for adjusting priority apply.

   STARTTIME (START)
        The time the process was started.

   PROCESSOR (CPU)
        The ID of the CPU the process last executed on.

   M_VIRT (VIRT)
        The size of the virtual memory of the process.

   M_RESIDENT (RES)
        The resident set size (text + data + stack) of the process (i.e. the size of the process's used physical memory).

   M_SHARE (SHR)
        The size of the process's shared pages.

   M_TRS (CODE)
        The text resident set size of the process (i.e. the size of the process's executable instructions).

   M_DRS (DATA)
        The data resident set size (data + stack) of the process (i.e. the size of anything except the process's executable instructions).

   M_LRS (LIB)
        The library size of the process.

   M_SWAP (SWAP)
        The size of the process's swapped pages.

   M_PSS (PSS)
        The proportional set size, same as M_RESIDENT but each page is divided by the number of processes sharing it.

   M_M_PSSWP (PSSWP)
        The proportional swap share of this mapping, unlike M_SWAP this does not take into account swapped out page of underlying shmem objects.

   ST_UID (UID)
        The user ID of the process owner.

   PERCENT_CPU (CPU%)
        The  percentage of the CPU time that the process is currently using.  This is the default way to represent CPU usage in Linux. Each process can consume up to 100% which means the
        full capacity of the core it is running on. This is sometimes called "Irix mode" e.g. in top(1).

   PERCENT_NORM_CPU (NCPU%)
        The percentage of the CPU time that the process is currently using normalized by CPU count. This is sometimes called "Solaris mode" e.g. in top(1).

   PERCENT_MEM (MEM%)
        The percentage of memory the process is currently using (based on the process's resident memory size, see M_RESIDENT above).

   USER The username of the process owner, or the user ID if the name can't be determined.

        On Linux the username is highlighted if the process has elevated privileges, i.e. if it has been started from binaries with file capabilities set or retained Linux  capabilities,
        via the ambient set, after switching from the root user.

   TIME (TIME+)
        The time, measured in clock ticks that the process has spent in user and system time (see UTIME, STIME above).

   NLWP The number of Light-Weight Processes (=threads) in the process.

   TGID The thread group ID.

   CTID OpenVZ container ID, a.k.a virtual environment ID.

   VPID OpenVZ process ID.

   VXID VServer process ID.

   RCHAR (RD_CHAR)
        The number of bytes the process has read.

   WCHAR (WR_CHAR)
        The number of bytes the process has written.

   SYSCR (RD_SYSC)
        The number of read(2) syscalls for the process.

   SYSCW (WR_SYSC)
        The number of write(2) syscalls for the process.

   RBYTES (IO_RBYTES)
        Bytes of read(2) I/O for the process.

   WBYTES (IO_WBYTES)
        Bytes of write(2) I/O for the process.

   CNCLWB (IO_CANCEL)
        Bytes of cancelled write(2) I/O.

   IO_READ_RATE (DISK READ)
        The I/O rate of read(2) in bytes per second, for the process.

   IO_WRITE_RATE (DISK WRITE)
        The I/O rate of write(2) in bytes per second, for the process.

   IO_RATE (DISK R/W)
        The I/O rate, IO_READ_RATE + IO_WRITE_RATE (see above).

   CGROUP
        Which cgroup the process is in. For a shortened view see the CCGROUP column below.

   CCGROUP
        Shortened view of the cgroup name that the process is in.  This performs some pattern-based replacements to shorten the displayed string and thus condense the information.
           /*.slice is shortened to /[*] (exceptions below)
           /system.slice is shortened to /[S]
           /user.slice is shortened to /[U]
           /user-*.slice is shortened to /[U:*] (directly preceding /[U] before dropped)
           /machine.slice is shortened to /[M]
           /machine-*.scope is shortened to /[SNC:*] (SNC: systemd nspawn container), uppercase for the monitor
           /lxc.monitor.* is shortened to /[LXC:*]
           /lxc.payload.* is shortened to /[lxc:*]
           /*.scope is shortened to /!*
           /*.service is shortened to /* (suffix removed)

        Encountered escape sequences (e.g. from systemd) inside the cgroup name are not decoded.

   OOM  OOM killer score.

   CTXT Incremental sum of voluntary and nonvoluntary context switches.

   IO_PRIORITY (IO)
        The I/O scheduling class followed by the priority if the class supports it:
           R for Realtime
           B for Best-effort
           id for Idle

   PERCENT_CPU_DELAY (CPUD%)
        The percentage of time spent waiting for a CPU (while runnable). Requires CAP_NET_ADMIN.

   PERCENT_IO_DELAY (IOD%)
        The percentage of time spent waiting for the completion of synchronous block I/O. Requires CAP_NET_ADMIN.

   PERCENT_SWAP_DELAY (SWAPD%)
        The percentage of time spent swapping in pages. Requires CAP_NET_ADMIN.

   AGRP The autogroup identifier for the process. Requires Linux CFS to be enabled.

   ANI  The autogroup nice value for the process autogroup. Requires Linux CFS to be enabled.

   All other flags
        Currently unsupported (always displays '-').

EXTERNAL LIBRARIES

   While  htop depends on most of the libraries it uses at build time there are two noteworthy exceptions to this rule. These exceptions both relate to data displayed in meters displayed
   in the header of htop and were intentionally created as optional runtime dependencies instead.  These exceptions are described below:

   libsystemd
          The bindings for libsystemd are used in the SystemD meter to determine the number of active services and the overall system state. Looking for the functions to determine  these
          information at runtime allows for builds to support these meters without forcing the package manager to install these libraries on systems that otherwise don't use systemd.

          Summary: no build time dependency, optional runtime dependency on libsystemd via dynamic loading, with systemctl(1) fallback.

   libsensors
          The  bindings  for  libsensors are used for the CPU temperature readings in the CPU usage meters if displaying the temperature is enabled through the setup screen. In order for
          htop to show these temperatures correctly though, a proper configuration of libsensors through its usual configuration files is assumed and that all  CPU  cores  correspond  to
          temperature  sensors  from the coretemp driver with core 0 corresponding to a sensor labelled "Core 0". The package temperature may be given as "Package id 0". If missing it is
          inferred as the maximum value from the available per-core readings.

          Summary: build time dependency on libsensors(3) C header files, optional runtime dependency on libsensors(3) via dynamic loading.

CONFIG FILES

   By default htop reads its configuration from the XDG-compliant path ~/.config/htop/htoprc.  The configuration file is overwritten upon clean exit by htop's in-program Setup configura‐
   tion, so it should not be hand-edited.  If no user configuration exists htop tries to read the system-wide configuration from /etc/htoprc and as a last resort, falls back to its  hard
   coded defaults.

   You may override the location of the configuration file using the $HTOPRC environment variable (so you can have multiple configurations for different machines that share the same home
   directory, for example).

   The  pcp-htop  utility  makes  use  of  htoprc  in  a  similar  way.   However,  pcp-htop  reads  its configuration from a path more conventionally used by Performance Co-Pilot tools,
   ~/.pcp/htop/htoprc, in order to provide separate configuration when both htop and pcp-htop are installed and in use.  pcp-htop supports additional configuration files below  the  same
   directory allowing new meters, columns and screen tabs to be added via the Setup screen (F2).  This displays additional Available Meters, Available Column and Screen Tabs for each me‐
   ter, column or screen configuration file.

   These pcp-htop configuration files are read once at startup.  The format of these files is described in detail in the pcp-htop(5) manual page.

   This  functionality makes available many thousands of Performance Co-Pilot metrics for display by pcp-htop, as well as the ability to display custom metrics added at individual sites.
   Applications and services instrumented using the OpenMetrics format https://openmetrics.io can also be displayed by pcp-htop if the pmdaopenmetrics(1) component is configured.

   The configuration for both htop and pcp-htop is only saved when a clean exit is performed. Sending any signal will cause all configuration changes to be lost.

MEMORY SIZES

   Memory sizes in htop are displayed in a human-readable form.  Sizes are printed in powers of 1024 using binary IEC units.  If no suffix is shown the units are implicitly K as  in  KiB
   (kibibyte, 1 KiB = 1024 bytes).

   The decision to use this convention was made in order to conserve screen space and make memory size representations consistent throughout htop as allocations are granular to full mem‐
   ory pages (4 KiB for most platforms).